Does bluex cholorox have cya9/3/2023 The level of aluminum sulfate in pickle juice is 110 ppm. The truth is, as you can see in the chart below, Alum will work well within a pH range of 5.8 to 8.0 with a bit of leeway on either end. The instructions on those two-pound containers we spoke of a moment ago generally call for a pH of 8.0 or higher. Precedence and Water treatment facility use dictates a pH between 6.5 and 7.2 for best results. What’s the Best pH for Floc?Įven under normal circumstances, the question of the correct pH to use is controversial. If the pH is too low, it will not work if the pH is too high, it will not work. The water needs to be at least 70 ☏ or better. Alum, those who have worked with the product, is also temperamental with particular pH and temperature requirements. To utilize the chemical to its full potential, you’ll need to follow water treatment center guidelines at least as far as dose. The dose rate you typically find on those containers will only treat cloudy water at best. Lower Cyanuric Acid Levels.Īluminum Sulfate Al₂(SO₄)₃ is the active ingredient in those two-pound cylindrical containers marketed as “Floc” that you see. Enthralled with the possibility, I spent the better part of the summer to see if I could create an alum-CyA removal method that would yield consistent and desirable results. I decided to perform a test and noted a dip in the level-nothing to write home about, but a drop nonetheless. Still, I had never thought of conducting a before and after the Cyanuric acid test until 2019, when a peer inquired about the possibility, noting a drop in ppm following a floc. Everything from removing Copper Stains from plaster to green to cleans on REO properties (foreclosed homes). I have used alum for many things over the years. At a 1:1 ratio with CyA (it takes one pound of melamine to pull one pound of Cyanuric acid out of solution), implementing this procedure would be a costly venture. I know adding melamine to the water will pull Cyanuric acid out of the solution, but melamine is a costly material. What made you think Aluminum Sulfate could be a solution? To View, our findings on Black Algae, visit us at Black Algae Myth BUSTED. If we can come up with a low-cost means of lowering CyA without the need for RO or water replacement, this will certainly benefit the individuals that employ these methods. I uncovered and had proven quite a bit of information that had been unknown up to that point. Please take a look at the Black Algae research I conducted last year. Maybe there is something that was missed or not yet considered. There are a lot of questions out there that we don’t have actual answers to. All of our field tests to date have been 100% out of pocket and with the volunteer assistance of industry peers. I’m not looking to capitalize on my findings. To fully comprehend the reason, you must first understand that all of the research I conduct intends to make the industry better. Maybe not bouncing off the walls with joy excitement, but a little enthusiasm toward the results. I wanted to share that information because I do think it is something to get excited about. The Great CyA Debate in it’s Entirety Below ⬇Īs I stated at the CyA debate at the IPSPE in New Orleans, I have had some success. I have been experimenting with Aluminum Sulfate Al₂(SO₄)₃ as a means to Lower Cyanuric Acid Level (C₃H₃N₃O₃). It’s not a statement that I wish I could retract. This was a conscious decision, not something that I just blurted out on the spur of the moment. Okay, so maybe I released this information before it has been deemed a proven method of reducing Cyanuric Acid levels chemically. Lower Cyanuric Acid Level, Video by Andrea Nannini of Hibiscus Pool & Spa. What chemical lowers cyanuric acid in swimming pools and actually works? Believe it or not, it’s sold in the spice aisle of your supermarket and is an ingredient in Pickles.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |